![]() ![]() ![]() (12) If different frequencies are added to the standard frequencies in the calibration, pricing will be made again. (11) Measurements of horn antennas will be made in vertical polarization, and measurements of other antennas will be made in horizontal polarization. (10) Calibration is done in the frequency range specified by the device manufacturer. (9) 50% of the calibration fee will be requested for your device that is found to be defective during the calibration. For frequencies 100 kHz – 26.5 GHz and 100 kHz – 50 GHz, 30% is added to the unit price. (6) Pricing is valid for 15 frequency points. (5) When phase measurement is made, 50% is added to the price. (4) Pricing is valid for single SIM card and 3 different traffic channels on a single frequency (900 MHz or 1800 MHz). (2) If measurement is requested at more than the specified frequency point, 40 EUR is charged for each additional frequency. (1) This service is within the scope of accreditation. Synthesiser Function Generator Calibration Synthesized Sweeper / Signal Generator CalibrationĮMC Test Equipment (Burst / Discontinuous Interference Analyzer) Calibration Measurement of Dielectric Properties of Materials (up to 50 GHz) Waveguide VNA Calibration Kit Calibration Reflection coefficient, VSWR, return loss measurement (45 MHz-26,5 GHz) (up to 20 frequencies)ĭirectional Coupler Calibration (≤ 2 GHz) Primary Level Computable Impedance Standard (airline) Calibration (up to 50GHz) Transmission Coefficient (up to 60 dB, 45 MHz-26,5 GHz) (up to 20 frequencies) Power Sensor Calibration (up to 26,5 GHz)Ĭalibration Factor of RF power sensor or thermistor mount (up to 15 frequency) Line Impedance Stabilization Network (LISN) Calibration Voltage/Current Probe Calibration (Frequency range for voltage probes: 150 kHz to 30 MHz, Frequency range for current probes: 30 Hz to 500 MHz, measuring range (-30 dBs) – (70 dBs)) Horn Antenna Calibration (Frequency range: 18 GHz – 40 GHz)Įlectric/Magnetic Field Probe Calibration ( Frequency range: 30 Hz – 32 kHz)Įlectric/Magnetic Field Probe Calibration( Frequency range: 30 Hz – 3 MHz)Įlectric/Magnetic Field Probe Calibration( Frequency range: 30 Hz – 30 MHz)Įlectric/Magnetic Field Probe Calibration( Frequency range: 30 Hz – 3 GHz)Įlectric/Magnetic Field Probe Calibration( Frequency range: 30 Hz – 20 GHz)Įlectric/Magnetic Field Probe Calibration( Frequency range: 30 Hz – 40 GHz) Horn Antenna Calibration (Frequency range: 1 GHz – 18 GHz) Universal x-ray fluorescence spectrometer for the elemental analysis for WEEE and RoHS compliance.Active-Passive Rod and Loop Antenna Calibration (Frequency range: 5 Hz – 30 MHz)īiconic, Bilog, Log-Periodic, Horn Antenna Calibration (Frequency range: 30 MHz – 1 GHz) Multiple Power Recycling:The system could recycle single/ 3 phase AC power and DC power.A fire distinguishing device FM-200 (Halogenated alkane) is built. Dummy proofs built from limit switches prevent incorrect installation.ī. Economy:The power recycling system could economize the power consumption about 70% to 80%.Ī.The burn-in system could raise the product reliability of high power system. We are offering equipment-level to system-level test instruments and systems. (Equipments Under Test) and relevant EMC standards, list all required items for EMC test setups. High Power Energy Recycling Burn-In System Coupling Decoupling Networks (CDNs) Comb Generators (Reference Sources) Conducted Immunity Test Generators. Request more information on MIL-STD-461 CS114 test equipment or order directly online. Including Two Programmable walk-in Temperature/Humidity Chamber.Ĭalibration Laboratory is recognized by the Taiwan Accreditation Foundation (TAF) with an ISO/IEC 17025 accreditation. Ther EMC Shop is a registered government supplier of test equipment focused on electromagnetic compatibility. It are able to provide rapid product temperature change rates and use varying levels of relative humidity to locate design problems, improving product quality and reliability. A Electrostatic Discharge(ESD) test site.The Lab execute these Radiation Test, Conduction Test, and Electrostatic Discharge(ESD) Test. (Electro-Magnetic Interference & Electro-Magnetic Susceptibility) It supports to test the product Electro-Magnetic Compatibility. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |